|
|
|
|
|
|
| |
Automobile Manufacturer Recall Data - Bmw Recalls 
Posted: 08-15-2008 | |
| 3 SERIES 5 SERIES 550I 6 SERIES 6-SERIES 650I 7 SERIES F650 CS F650 GS F650 GS DAKAR F800 S F800 ST G650X CHALLENGE G650X COUNTRY G650X MOTO K SERIES K1200 GT K1200 LT K1200 R K1200 R SPORT K1200 S R 1200 GS R 1200 ST R SERIES R1150 R R1150 RT R1200 GS R1200 GS ADVENTURE R1200 HP2 R1200 R R1200 RT R1200 S R1200 ST R850 R X5 Z4 | |
| 3 SERIES RECALLS | Top |
| 2006 BMW 3 SERIES Manufactured between: 06/30/2006 and 07/14/2006 Defect: on certain vehicles, one of the suspension control arm and swivel bearing connection bolts was not tightened correctly. the bolted connection could loosen. Consequence: the bolted connection could break which could impair vehicle handling and control, increasing the risk of a crash. Action: dealers will inspect the bolted connection and, if necessary, adjust the connection. in some cases, it may be necessary to replace the suspension control arm and the swivel bearing. the recall began on november 21, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 10/18/2006 | |
| 5 SERIES RECALLS | Top |
| 2006 BMW 5 SERIES Manufactured between: 01/05/2006 and 04/26/2006 Defect: on certain passenger vehicles, the lower rubber mount of the rear shock absorbers may not have been manufactured to specifications and may not adhere correctly to its housing within the shock absorber. Consequence: the bushing could loosen and over time could separate from its housing. the driver will experience impaired vehicle handling and control increasing the risk of a crash. Action: dealers will replace the rear shock absorber free of charge. the recall began on september 13, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 07/26/2006 | |
| 2006 BMW 5 SERIES Manufactured between: 02/13/2006 and 02/13/2006 Defect: on certain passenger vehicles, the nuts which secure the front axle control arm and tension strut to the front wheel hub may not have been tightened to specification. over time the nuts could loosen and the control arm and tension strut could be damaged. Consequence: vehicle handling and control could compromise increasing the risk of a crash. Action: dealers will retighten the front axle control arm and tension strut nuts to the correct specifications free of charge. the recall began on june 28, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/30/2006 | |
| 2006 BMW 5 SERIES Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2005 BMW 5 SERIES Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2004 BMW 5 SERIES Manufactured between: 06/17/2003 and 04/30/2004 Defect: on certain passenger vehicles equipped with front seat heating systems, upon entering and exiting the vehicle, excessive contact with the side bolster that is contained in the seat's backrest may damage the heating mat located in this area. if such damage were to occur, with the system turned on, the vehicle occupant may feel excessive heat from this area. Consequence: it is possible that the heating mat in the backrest's side bolster could overheat and damage, or melt a small hole in, this area of the seat cover. if this happened, it could lead to an occupant being burned. Action: dealers will modify the seat heating circuit. the recall is expected to begin during december 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 12/06/2004 | |
| 2004 BMW 5 SERIES Manufactured between: 05/12/2004 and 07/06/2004 Defect: on certain passenger vehicles equipped with 8 and 12 cylinder engines, the digital engine management control (emc) units were not produced according to specifications. Consequence: as a result, engine stalling will occur after a short period of operation. the vehicle may not be able to restart. also, a loss of power steering and, after repeated actuation of the brake pedal, a loss of brake power assist will occur. these conditions could result in a vehicle crash. Action: dealers will install a new digital engine management control unit. the recall began on july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 07/14/2004 | |
| 2004 BMW 5 SERIES Manufactured between: 09/04/2003 and 04/28/2004 Defect: on certain passenger vehicles equipped with 8-cylinder engines, a circular retention clip at the quick-release coupling along the fuel supply line was inadvertently not installed. Consequence: in the event of a severe frontal crash, the quick-release coupling could separate causing fuel leakage. fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will install a circular retention clip at the quick-release coupling along the fuel supply line. the recall began on july 5, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 06/23/2004 | |
| 550I RECALLS | Top |
| 2008 BMW 550I Manufactured between: 08/26/2005 and 06/14/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 2007 BMW 550I Manufactured between: 08/26/2005 and 06/14/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 2006 BMW 550I Manufactured between: 08/26/2005 and 06/14/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 6 SERIES RECALLS | Top |
| 2006 BMW 6 SERIES Manufactured between: 01/05/2006 and 04/26/2006 Defect: on certain passenger vehicles, the lower rubber mount of the rear shock absorbers may not have been manufactured to specifications and may not adhere correctly to its housing within the shock absorber. Consequence: the bushing could loosen and over time could separate from its housing. the driver will experience impaired vehicle handling and control increasing the risk of a crash. Action: dealers will replace the rear shock absorber free of charge. the recall began on september 13, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 07/26/2006 | |
| 2006 BMW 6 SERIES Manufactured between: 02/13/2006 and 02/13/2006 Defect: on certain passenger vehicles, the nuts which secure the front axle control arm and tension strut to the front wheel hub may not have been tightened to specification. over time the nuts could loosen and the control arm and tension strut could be damaged. Consequence: vehicle handling and control could compromise increasing the risk of a crash. Action: dealers will retighten the front axle control arm and tension strut nuts to the correct specifications free of charge. the recall began on june 28, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/30/2006 | |
| 2006 BMW 6 SERIES Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2005 BMW 6 SERIES Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2004 BMW 6 SERIES Manufactured between: 05/12/2004 and 07/06/2004 Defect: on certain passenger vehicles equipped with 8 and 12 cylinder engines, the digital engine management control (emc) units were not produced according to specifications. Consequence: as a result, engine stalling will occur after a short period of operation. the vehicle may not be able to restart. also, a loss of power steering and, after repeated actuation of the brake pedal, a loss of brake power assist will occur. these conditions could result in a vehicle crash. Action: dealers will install a new digital engine management control unit. the recall began on july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 07/14/2004 | |
| 2004 BMW 6 SERIES Manufactured between: 09/04/2003 and 04/28/2004 Defect: on certain passenger vehicles equipped with 8-cylinder engines, a circular retention clip at the quick-release coupling along the fuel supply line was inadvertently not installed. Consequence: in the event of a severe frontal crash, the quick-release coupling could separate causing fuel leakage. fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will install a circular retention clip at the quick-release coupling along the fuel supply line. the recall began on july 5, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 06/23/2004 | |
| 6-SERIES RECALLS | Top |
| 2007 BMW 6-SERIES Manufactured between: 09/01/2006 and 01/15/2007 Defect: certain passenger vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 208, 'occupant crash protection.' the front passenger seat has a sensing system to detect if the seat is occupied. this sensing is programmed to detect if the seat is occupied by a small adult or certain child restraint seats. placing certain child seats on the front passenger seat is designed to result in the automatic deactivation of the front seat passenger's air bag. Consequence: in some cases, the sensing system may misinterpret a properly seated small adult as one of these specific child seats, resulting in deactivation of the front passenger air bag when the air bag might be beneficial for the adult, increasing the risk of injury in a crash. Action: dealers will replace the front passenger seat sensor. the recall began on may 21, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 04/25/2007 | |
| 650I RECALLS | Top |
| 2007 BMW 650I Manufactured between: 08/26/2005 and 06/14/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 2006 BMW 650I Manufactured between: 08/26/2005 and 06/14/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 7 SERIES RECALLS | Top |
| 2006 BMW 7 SERIES Manufactured between: 01/05/2006 and 04/26/2006 Defect: on certain passenger vehicles, the lower rubber mount of the rear shock absorbers may not have been manufactured to specifications and may not adhere correctly to its housing within the shock absorber. Consequence: the bushing could loosen and over time could separate from its housing. the driver will experience impaired vehicle handling and control increasing the risk of a crash. Action: dealers will replace the rear shock absorber free of charge. the recall began on september 13, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 07/26/2006 | |
| 2004 BMW 7 SERIES Manufactured between: 02/26/2003 and 06/09/2004 Defect: on certain passenger vehicles equipped with front seat heating systems, upon entering and exiting the vehicle, excessive contact with the side bolster that is contained in the seat's backrest may damage the heating mat located in this area. if such damage were to occur, with the system turned on, the vehicle occupant may feel excessive heat from this area. Consequence: it is possible that the heating mat in the backrest's side bolster could overheat and damage, or melt a small hole in, this area of the seat cover. if this happened, it could lead to an occupant being burned. Action: dealers will modify the seat heating circuit. the recall is expected to begin during december 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 12/06/2004 | |
| 2004 BMW 7 SERIES Manufactured between: 03/01/2004 and 06/02/2004 Defect: on certain passenger vehicles, the software programming of the driver's seat occupant detection system (ods) may not be able to reliably determine if the driver's seat is occupied. Consequence: in certain crash conditions, the driver's front air bag, head protection system, safety belt pretensioner, and knee air bag may not deploy, increasing the risk of injury to a seat occupant. Action: dealers will reprogram the software for the driver's seat occupant detection system. the recall began october 13, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 08/09/2004 | |
| 2004 BMW 7 SERIES Manufactured between: 05/12/2004 and 07/06/2004 Defect: on certain passenger vehicles equipped with 8 and 12 cylinder engines, the digital engine management control (emc) units were not produced according to specifications. Consequence: as a result, engine stalling will occur after a short period of operation. the vehicle may not be able to restart. also, a loss of power steering and, after repeated actuation of the brake pedal, a loss of brake power assist will occur. these conditions could result in a vehicle crash. Action: dealers will install a new digital engine management control unit. the recall began on july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 07/14/2004 | |
| F650 CS RECALLS | Top |
| 2004 BMW F650 CS Manufactured between: 01/01/2002 and 09/30/2003 Defect: on certain motorcycles, the plastic fuel pump flange could come into contact with a sufficient amount of acid or chemical compounds containing acidic elements, such as battery acid or certain cleaning products. Consequence: the flange could become brittle, crack, and allow fuel to escape from the fuel tank. fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will install an acid-resistant cap over the fuel pump flange. the recall began june 10, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 05/19/2004 | |
| F650 GS RECALLS | Top |
| 2007 BMW F650 GS Manufactured between: 06/23/2006 and 08/31/2006 Defect: on certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. the load-bearing capability of the side stand is affected. as a result, the side stand could fail. Consequence: if this occurred when the motorcycle was parked, the motorcycle could fall to the ground and injure a person sitting on the motorcycle or a person nearby. Action: dealers will install a new frame bottom section free of charge. the recall began on june 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 04/03/2007 | |
| 2006 BMW F650 GS Manufactured between: 06/23/2006 and 08/31/2006 Defect: on certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. the load-bearing capability of the side stand is affected. as a result, the side stand could fail. Consequence: if this occurred when the motorcycle was parked, the motorcycle could fall to the ground and injure a person sitting on the motorcycle or a person nearby. Action: dealers will install a new frame bottom section free of charge. the recall began on june 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 04/03/2007 | |
| F650 GS DAKAR RECALLS | Top |
| 2007 BMW F650 GS DAKAR Manufactured between: 06/23/2006 and 08/31/2006 Defect: on certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. the load-bearing capability of the side stand is affected. as a result, the side stand could fail. Consequence: if this occurred when the motorcycle was parked, the motorcycle could fall to the ground and injure a person sitting on the motorcycle or a person nearby. Action: dealers will install a new frame bottom section free of charge. the recall began on june 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 04/03/2007 | |
| 2006 BMW F650 GS DAKAR Manufactured between: 06/23/2006 and 08/31/2006 Defect: on certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. the load-bearing capability of the side stand is affected. as a result, the side stand could fail. Consequence: if this occurred when the motorcycle was parked, the motorcycle could fall to the ground and injure a person sitting on the motorcycle or a person nearby. Action: dealers will install a new frame bottom section free of charge. the recall began on june 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 04/03/2007 | |
| F800 S RECALLS | Top |
| 2008 BMW F800 S Manufactured between: 08/03/2006 and 08/22/2007 Defect: bmw is recalling 1,980 my 2007-2008 f800 s and f800 st motorcycles. due to the routing of the fuel tank breather hose, pressure equalization inside the fuel tank is possible only to a limited extent. consequently, at high ambient temperatures, the fuel tank can deform. if this happened at the point where the fuel tank is shaped to provide clearance for the rear wheel, then, in combination with a large payload, the bottom of the tank could rub against the rear wheel. Consequence: if this occurred, it is possible that a leak could develop in the tank. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will reroute the fuel tank breather hose. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| 2007 BMW F800 S Manufactured between: 03/28/2007 and 05/03/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW F800 S Manufactured between: 08/03/2006 and 08/22/2007 Defect: bmw is recalling 1,980 my 2007-2008 f800 s and f800 st motorcycles. due to the routing of the fuel tank breather hose, pressure equalization inside the fuel tank is possible only to a limited extent. consequently, at high ambient temperatures, the fuel tank can deform. if this happened at the point where the fuel tank is shaped to provide clearance for the rear wheel, then, in combination with a large payload, the bottom of the tank could rub against the rear wheel. Consequence: if this occurred, it is possible that a leak could develop in the tank. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will reroute the fuel tank breather hose. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| F800 ST RECALLS | Top |
| 2008 BMW F800 ST Manufactured between: 08/03/2006 and 11/08/2007 Defect: bmw is recalling 1,980 my 2007-2008 f800 s and f800 st motorcycles. due to the routing of the fuel tank breather hose, pressure equalization inside the fuel tank is possible only to a limited extent. consequently, at high ambient temperatures, the fuel tank can deform. if this happened at the point where the fuel tank is shaped to provide clearance for the rear wheel, then, in combination with a large payload, the bottom of the tank could rub against the rear wheel. Consequence: if this occurred, it is possible that a leak could develop in the tank. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will reroute the fuel tank breather hose. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| 2007 BMW F800 ST Manufactured between: 03/26/2007 and 05/05/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW F800 ST Manufactured between: 08/03/2006 and 11/08/2007 Defect: bmw is recalling 1,980 my 2007-2008 f800 s and f800 st motorcycles. due to the routing of the fuel tank breather hose, pressure equalization inside the fuel tank is possible only to a limited extent. consequently, at high ambient temperatures, the fuel tank can deform. if this happened at the point where the fuel tank is shaped to provide clearance for the rear wheel, then, in combination with a large payload, the bottom of the tank could rub against the rear wheel. Consequence: if this occurred, it is possible that a leak could develop in the tank. fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will reroute the fuel tank breather hose. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| G650X CHALLENGE RECALLS | Top |
| 2007 BMW G650X CHALLENGE Manufactured between: 02/12/2007 and 03/14/2007 Defect: bmw is recalling 744 my 2007 g650x challenger and country motorcycles. the motorcycles may have had the wrong circular clip installed on the left hand side of the rear wheel bearing guide. this circlip can rub against a spacer bushing, creating metal shavings which may enter the wheel bearing, causing it to fail and the antilock brake system (abs) may malfunction. this would be indicated by illumination of the abs warning lamp. Consequence: if this happened, the brakes would remain fully available to slow and stop the motorcycle. depending on traffic and road conditions as well as a rider's reactions, could increase the risk of a crash. Action: dealers will check and install a correct circlip, along with a new spacer bushing, wheel bearings, and shaft sealing rings free of charge. the recall is expected to begin during march 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 03/11/2008 | |
| 2007 BMW G650X CHALLENGE Manufactured between: 08/01/2006 and 03/21/2007 Defect: bmw is recalling 1,391 my 2007 g650x challenge, country, and moto motorcycles. the fuel lines may have been damaged during production, and could develop a leak. the leak could occur either through the fabric inlay at the end of the line, or, through a crack in the actual line. Consequence: fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will inspect and replace the fuel lines free of charge. the recall is expected to begin during march 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 03/11/2008 | |
| 2007 BMW G650X CHALLENGE Manufactured between: 01/05/2007 and 02/23/2007 Defect: on certain motorcycles, the fuel pump wiring set has not been manufactured according to specification. the contacts in the plug for the fuel pump can break. Consequence: the fuel pump will fail and fuel delivery to the engine would cease causing the engine to stall increasing the risk of a crash. Action: dealers will replace the fuel pump unit wiring set free of charge. the recall began on october 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/22/2007 | |
| 2007 BMW G650X CHALLENGE Manufactured between: 01/20/2007 and 08/06/2007 Defect: on certain motorcycles, a left-side chain tensioner has been incorrectly installed on the right side. as a result, a hex nut, which is used to secure the chain tensioner, is improperly seated against the tensioner. Consequence: loosening of the chain tensioner and the rear wheel axle may occur. this could lead to a condition in which the motorcycle is unstable, increasing the risk of a crash. Action: dealers will install a new right side chain tensioner free of charge. the recall began on november 13, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/15/2007 | |
| G650X COUNTRY RECALLS | Top |
| 2007 BMW G650X COUNTRY Manufactured between: 02/20/2007 and 03/21/2007 Defect: bmw is recalling 744 my 2007 g650x challenger and country motorcycles. the motorcycles may have had the wrong circular clip installed on the left hand side of the rear wheel bearing guide. this circlip can rub against a spacer bushing, creating metal shavings which may enter the wheel bearing, causing it to fail and the antilock brake system (abs) may malfunction. this would be indicated by illumination of the abs warning lamp. Consequence: if this happened, the brakes would remain fully available to slow and stop the motorcycle. depending on traffic and road conditions as well as a rider's reactions, could increase the risk of a crash. Action: dealers will check and install a correct circlip, along with a new spacer bushing, wheel bearings, and shaft sealing rings free of charge. the recall is expected to begin during march 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 03/11/2008 | |
| 2007 BMW G650X COUNTRY Manufactured between: 08/01/2006 and 03/22/2007 Defect: bmw is recalling 1,391 my 2007 g650x challenge, country, and moto motorcycles. the fuel lines may have been damaged during production, and could develop a leak. the leak could occur either through the fabric inlay at the end of the line, or, through a crack in the actual line. Consequence: fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will inspect and replace the fuel lines free of charge. the recall is expected to begin during march 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 03/11/2008 | |
| 2007 BMW G650X COUNTRY Manufactured between: 01/05/2007 and 02/20/2007 Defect: on certain motorcycles, the fuel pump wiring set has not been manufactured according to specification. the contacts in the plug for the fuel pump can break. Consequence: the fuel pump will fail and fuel delivery to the engine would cease causing the engine to stall increasing the risk of a crash. Action: dealers will replace the fuel pump unit wiring set free of charge. the recall began on october 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/22/2007 | |
| 2007 BMW G650X COUNTRY Manufactured between: 01/20/2007 and 03/06/2007 Defect: on certain motorcycles, a left-side chain tensioner has been incorrectly installed on the right side. as a result, a hex nut, which is used to secure the chain tensioner, is improperly seated against the tensioner. Consequence: loosening of the chain tensioner and the rear wheel axle may occur. this could lead to a condition in which the motorcycle is unstable, increasing the risk of a crash. Action: dealers will install a new right side chain tensioner free of charge. the recall began on november 13, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/15/2007 | |
| G650X MOTO RECALLS | Top |
| 2007 BMW G650X MOTO Manufactured between: 08/01/2006 and 03/14/2007 Defect: bmw is recalling 1,391 my 2007 g650x challenge, country, and moto motorcycles. the fuel lines may have been damaged during production, and could develop a leak. the leak could occur either through the fabric inlay at the end of the line, or, through a crack in the actual line. Consequence: fuel leakage, in the presence of an ignition source, could result in a fire. Action: dealers will inspect and replace the fuel lines free of charge. the recall is expected to begin during march 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 03/11/2008 | |
| 2007 BMW G650X MOTO Manufactured between: 01/05/2007 and 02/21/2007 Defect: on certain motorcycles, the fuel pump wiring set has not been manufactured according to specification. the contacts in the plug for the fuel pump can break. Consequence: the fuel pump will fail and fuel delivery to the engine would cease causing the engine to stall increasing the risk of a crash. Action: dealers will replace the fuel pump unit wiring set free of charge. the recall began on october 1, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/22/2007 | |
| 2007 BMW G650X MOTO Manufactured between: 01/20/2007 and 03/06/2007 Defect: on certain motorcycles, a left-side chain tensioner has been incorrectly installed on the right side. as a result, a hex nut, which is used to secure the chain tensioner, is improperly seated against the tensioner. Consequence: loosening of the chain tensioner and the rear wheel axle may occur. this could lead to a condition in which the motorcycle is unstable, increasing the risk of a crash. Action: dealers will install a new right side chain tensioner free of charge. the recall began on november 13, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/15/2007 | |
| K SERIES RECALLS | Top |
| 2004 BMW K SERIES Manufactured between: 05/01/2000 and 12/31/2003 Defect: on certain motorcycles, the o-ring in fuel line quick-disconnect coupling could become damaged and lead to a fuel leak. there is also a problem involving crimp-type hose clamps, which can result in a fuel leak. Consequence: fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will inspect and, if necessary, adjust all crimp-type hose clamps. also, all fuel line quick-disconnect couplings will be inspected. if a leak is detected, the quick-disconnect o-ring will be replaced. if damaged, the coupling will be replaced. owner notification began on april 30, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 01/15/2004 | |
| K1200 GT RECALLS | Top |
| 2008 BMW K1200 GT Manufactured between: 01/11/2008 and 01/16/2008 Defect: bmw is recalling 75 my 2008 k1200 s and gt motorcycles. the fasteners used to secure the front brake-disc may not be long enough to ensure a secure mounting. over time, these fasteners could loosen. if that happened, the brake disc would no longer be securely mounted. Consequence: failure to observe the following precautions, in conjunction with traffic and road conditions, and the rider's reactions, could increase the risk of a crash. Action: dealers will inspect and install a longer front brake disc fasteners and reroute the sensor cable free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/04/2008 | |
| 2008 BMW K1200 GT Manufactured between: 12/11/2007 and 01/09/2008 Defect: bmw is recalling 30 my 2008 k1200 s and k1200 gt motorcycles. a set screw may not have been installed at its specific location within the oil duct. consequently, an adequate supply of oil may not circulate within the engine. Consequence: it is possible that connecting rod and crankshaft damage could occur. if this happened, the engine could seize. if the motorcycle was in gear, engine seizing could result in lock-up of the rear tire, increasing the risk of a crash. Action: dealers will install a set screw in the oil duct. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| 2007 BMW K1200 GT Manufactured between: 04/02/2007 and 05/12/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW K1200 GT Manufactured between: 11/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 GT Manufactured between: 11/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2005 BMW K1200 GT Manufactured between: 11/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| K1200 LT RECALLS | Top |
| 2005 BMW K1200 LT Manufactured between: 01/05/2004 and 03/13/2004 Defect: on certain motorcycles, at lower temperatures, wiring within the anti-theft control unit may press against the fuel pump relay. the fuel pump relay contacts could open, interrupting the fuel supply to the engine, resulting in stalling. Consequence: if stalling were to occur, the driver would be unable to maintain speed or accelerate, increasing the risk of a crash. Action: dealers will inspect and, if necessary, replace the anti-theft control unit. the recall began october 4, 2004. customers should contact bmw at 1-800-831-1117. Recall Date: 09/09/2004 | |
| 2005 BMW K1200 LT Manufactured between: 04/01/2004 and 04/30/2004 Defect: on certain motorcycles, an incorrect sealing ring was mounted to the piston of the rear brake master cylinder. Consequence: if only the rear brake were applied during riding, insufficient braking pressure would be available to slow the motorcycle, which could increase the risk of a crash. Action: dealers will replace the rear brake master cylinder. the recall began july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 06/23/2004 | |
| K1200 R RECALLS | Top |
| 2007 BMW K1200 R Manufactured between: 04/02/2007 and 05/11/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW K1200 R Manufactured between: 04/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 R Manufactured between: 04/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 R Manufactured between: 04/01/2005 and 12/31/2005 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2005 BMW K1200 R Manufactured between: 04/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2004 BMW K1200 R Manufactured between: 04/30/2004 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| K1200 R SPORT RECALLS | Top |
| 2007 BMW K1200 R SPORT Manufactured between: 04/02/2007 and 05/12/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW K1200 R SPORT Manufactured between: 06/23/2005 and 07/19/2007 Defect: on certain motorcycles, during long periods of riding at sustained high engine rpm, vibration within the brake fluid reservoir can cause the brake fluid to foam. this could allow air to enter the front brake system which could lead to a loss of front braking efficiency. Consequence: air in the brake system can lead to a loss of braking capability, increasing the risk of a crash. Action: dealers will bleed the front brakes and install a damper weight in the brake fluid reservoir. this weight will dampen possible vibrations that can cause foaming of the brake fluid. the recall began on december 14, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/02/2007 | |
| 2007 BMW K1200 R SPORT Manufactured between: 06/30/2005 and 12/31/2006 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 R SPORT Manufactured between: 06/23/2005 and 07/19/2007 Defect: on certain motorcycles, during long periods of riding at sustained high engine rpm, vibration within the brake fluid reservoir can cause the brake fluid to foam. this could allow air to enter the front brake system which could lead to a loss of front braking efficiency. Consequence: air in the brake system can lead to a loss of braking capability, increasing the risk of a crash. Action: dealers will bleed the front brakes and install a damper weight in the brake fluid reservoir. this weight will dampen possible vibrations that can cause foaming of the brake fluid. the recall began on december 14, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/02/2007 | |
| 2006 BMW K1200 R SPORT Manufactured between: 06/30/2005 and 12/31/2006 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2005 BMW K1200 R SPORT Manufactured between: 06/23/2005 and 07/19/2007 Defect: on certain motorcycles, during long periods of riding at sustained high engine rpm, vibration within the brake fluid reservoir can cause the brake fluid to foam. this could allow air to enter the front brake system which could lead to a loss of front braking efficiency. Consequence: air in the brake system can lead to a loss of braking capability, increasing the risk of a crash. Action: dealers will bleed the front brakes and install a damper weight in the brake fluid reservoir. this weight will dampen possible vibrations that can cause foaming of the brake fluid. the recall began on december 14, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/02/2007 | |
| 2005 BMW K1200 R SPORT Manufactured between: 06/30/2005 and 12/31/2006 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| K1200 S RECALLS | Top |
| 2008 BMW K1200 S Manufactured between: 10/30/2007 and 01/16/2008 Defect: bmw is recalling 75 my 2008 k1200 s and gt motorcycles. the fasteners used to secure the front brake-disc may not be long enough to ensure a secure mounting. over time, these fasteners could loosen. if that happened, the brake disc would no longer be securely mounted. Consequence: failure to observe the following precautions, in conjunction with traffic and road conditions, and the rider's reactions, could increase the risk of a crash. Action: dealers will inspect and install a longer front brake disc fasteners and reroute the sensor cable free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/04/2008 | |
| 2008 BMW K1200 S Manufactured between: 12/11/2007 and 01/10/2008 Defect: bmw is recalling 30 my 2008 k1200 s and k1200 gt motorcycles. a set screw may not have been installed at its specific location within the oil duct. consequently, an adequate supply of oil may not circulate within the engine. Consequence: it is possible that connecting rod and crankshaft damage could occur. if this happened, the engine could seize. if the motorcycle was in gear, engine seizing could result in lock-up of the rear tire, increasing the risk of a crash. Action: dealers will install a set screw in the oil duct. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-331-1117. Recall Date: 06/02/2008 | |
| 2007 BMW K1200 S Manufactured between: 04/02/2007 and 05/10/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW K1200 S Manufactured between: 04/01/2003 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 S Manufactured between: 04/01/2003 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2006 BMW K1200 S Manufactured between: 12/01/2004 and 12/31/2005 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2005 BMW K1200 S Manufactured between: 04/01/2003 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| 2005 BMW K1200 S Manufactured between: 12/01/2004 and 12/31/2005 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2005 BMW K1200 S Manufactured between: 05/18/2004 and 04/29/2005 Defect: on certain motorcycles, there could be a problem with the routing of the integral anti-lock-brake system (iabs) sensor cable if service has been performed on the motorcycle, for example, a front tire change. Consequence: the sensor cable can come into contact with, and rub against, the front brake disk. if the chafing becomes severe, it is possible to lose the abs function increasing the risk of a crash. Action: dealers will inspect and attach an additional retaining clip to the iabs sensor cable free of charge. the recall began september 23, 2005. owners may contact bmw at 1-800-831-1117. Recall Date: 08/19/2005 | |
| 2004 BMW K1200 S Manufactured between: 04/01/2003 and 01/31/2007 Defect: on certain motorcycles, frequent short trips particularly during cold temperatures, can cause water to accumulate in the oil tank, and when the engine is running, escaping water vapor can condense on the oil tank air bleed valve. in freezing temperatures, this water could freeze and block the air bleed valve. Consequence: it is possible that a pressure build up in the oil tank could cause it to rupture, allowing oil to leak onto the rear tire. an oil leak could cause a fire. oil on the rear tire could cause loss of control. Action: dealers will install a new oil tank cap containing a valve to prevent overpressure in the tank free of charge. the recall began on april 10, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 02/23/2007 | |
| R 1200 GS RECALLS | Top |
| 2004 BMW R 1200 GS Manufactured between: 11/03/2003 and 06/29/2004 Defect: on certain motorcycles, the defect involves a water leak around the fuel pump that is integrated within the fuel tank. an o-ring seal attached to the pump's electronic housing does not meet specifications and water can bypass this seal and contact the pump electronics. Consequence: engine stalling, or a failure to start, could occur without prior warning. if stalling were to occur while the motorcycle was being driven, the rider would be unable to maintain speed or accelerate and a crash could occur without prior warning. Action: dealers will replace a sealing ring. if the fuel pump electronic unit is corroded, it will be replaced free of charge. the recall began may 9, 2005. additional my 2005 r1200 gs motorcycles were added to this recall in december 2005. owners of my 2005 motorcycles will receive a notification during february 2006 through august 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 03/03/2005 | |
| R 1200 ST RECALLS | Top |
| 2005 BMW R 1200 ST Manufactured between: 02/01/2005 and 11/30/2005 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2005 BMW R 1200 ST Manufactured between: 12/01/2004 and 01/31/2006 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| 2005 BMW R 1200 ST Manufactured between: 12/01/2004 and 03/03/2005 Defect: on certain motorcycles, exposure of the throttle housing to road debris could fall and become caught between the throttle-body and the engine block. Consequence: this could restrict movement of the throttle-cable pulley that, in turn, could affect throttle operation and increase the risk of a crash. Action: dealers will install a cover over the throttle-cable pulley free of charge. the recall began on may 10, 2005. owners may contact bmw at 1-800-831-1117. Recall Date: 04/27/2005 | |
| R SERIES RECALLS | Top |
| 2004 BMW R SERIES Manufactured between: 05/01/2000 and 12/31/2003 Defect: on certain motorcycles, the o-ring in fuel line quick-disconnect coupling could become damaged and lead to a fuel leak. there is also a problem involving crimp-type hose clamps, which can result in a fuel leak. Consequence: fuel leakage in the presence of an ignition source could result in a fire. Action: dealers will inspect and, if necessary, adjust all crimp-type hose clamps. also, all fuel line quick-disconnect couplings will be inspected. if a leak is detected, the quick-disconnect o-ring will be replaced. if damaged, the coupling will be replaced. owner notification began on april 30, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 01/15/2004 | |
| R1150 R RECALLS | Top |
| 2004 BMW R1150 R Manufactured between: 10/01/2003 and 11/30/2003 Defect: on certain motorcycles, the front spring strut upper stud bolt weld can fail. this could cause the bolt to break. Consequence: if this happens, the rider may not be able to control the motorcycle, which could cause a crash without warning. Action: dealers will replace the front spring strut. the recall began during june 2004. owners should contact bmw at 1-800-331-1117. Recall Date: 05/19/2004 | |
| R1150 RT RECALLS | Top |
| 2004 BMW R1150 RT Manufactured between: 04/01/2004 and 04/30/2004 Defect: on certain motorcycles, an incorrect sealing ring was mounted to the piston of the rear brake master cylinder. Consequence: if only the rear brake were applied during riding, insufficient braking pressure would be available to slow the motorcycle, which could increase the risk of a crash. Action: dealers will replace the rear brake master cylinder. the recall began july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 06/23/2004 | |
| R1200 GS RECALLS | Top |
| 2008 BMW R1200 GS Manufactured between: 02/12/2008 and 02/18/2008 Defect: bmw is recalling 46 my 2008 r1200 r, r1200 gs, and r1200 gs adventure motorcycles. due to a material defect in the intermediate shaft of the transmission, the shaft could break. if this occurred, it is possible for the transmission to seize. Consequence: if this happened, lock-up of the rear tire could occur. it is also possible for the transmission housing to break. if this happened, oil could leak onto the rear whee, increasing the risk of a crash. Action: dealers will replace the gearbox. the recall is expected to begin during july 2008. owners should contact bmw at 1-800-331-1117. Recall Date: 07/01/2008 | |
| 2007 BMW R1200 GS Manufactured between: 07/06/2006 and 07/06/2007 Defect: bmw is recalling 3,248 my 2007-2008 r1200r, my 2006-2007 r1200 gs and my 2007 r1200 st motorcycles. due to the current routing of the front brake lines, it is possible that during riding, the brake lines could be under strain. if the vibration/strain is significant, the brake lines could split and start to develop a leak. if the leak became significant, brake fluid could escape. if this happened, the level of fluid in the reservoir of the front brake system could drop. Consequence: if fluid level drops significantly, the front brakes could fail increasing the risk of a crash. Action: dealers will inspect and install new brake lines with a modified routing free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/05/2008 | |
| 2006 BMW R1200 GS Manufactured between: 07/06/2006 and 07/06/2007 Defect: bmw is recalling 3,248 my 2007-2008 r1200r, my 2006-2007 r1200 gs and my 2007 r1200 st motorcycles. due to the current routing of the front brake lines, it is possible that during riding, the brake lines could be under strain. if the vibration/strain is significant, the brake lines could split and start to develop a leak. if the leak became significant, brake fluid could escape. if this happened, the level of fluid in the reservoir of the front brake system could drop. Consequence: if fluid level drops significantly, the front brakes could fail increasing the risk of a crash. Action: dealers will inspect and install new brake lines with a modified routing free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/05/2008 | |
| 2006 BMW R1200 GS Manufactured between: 09/06/2006 and 10/13/2006 Defect: on certain motorcycles, the tire inflation valve hole in the rim of the cross-spoke wheel which is equipped with the optional tire pressure monitoring system (tpm) was incorrectly manufactured. a leak may develop at this location possibly causing sudden deflation of the tire. Consequence: if this happened, motorcycle handling and control would be compromised, increasing the risk of a crash. Action: dealers will temporarily deactivate the tpm system, remove the corresponding valves and integral tpm sensors, and then replace them with standard valves. when a permanent repair is available, owners will be notified to bring their vehicles in for reactivation of the tpm system and replacement of the integral tpm sensors and valves. the recall began on january 12, 2007. owners may contact bmw at 1-800-331-1117. Recall Date: 12/21/2006 | |
| 2006 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2006 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| 2006 BMW R1200 GS Manufactured between: 01/20/2006 and 01/24/2006 Defect: on certain motorcycles, the clutch components could become loose while the motorcycle is being operated. Consequence: if this happened, the components could exit through the engine casting increasing the risk of a crash. Action: dealers will install new clutch components free of charge. all motorcycles are located at dealers. no motorcycles have been sold to customers. Recall Date: 04/04/2006 | |
| 2005 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2005 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| 2005 BMW R1200 GS Manufactured between: 11/02/2003 and 03/03/2005 Defect: on certain motorcycles, exposure of the throttle housing to road debris could fall and become caught between the throttle-body and the engine block. Consequence: this could restrict movement of the throttle-cable pulley that, in turn, could affect throttle operation and increase the risk of a crash. Action: dealers will install a cover over the throttle-cable pulley free of charge. the recall began on may 10, 2005. owners may contact bmw at 1-800-831-1117. Recall Date: 04/27/2005 | |
| 2005 BMW R1200 GS Manufactured between: 07/01/2004 and 01/01/2005 Defect: on certain motorcycles, the defect involves a water leak around the fuel pump that is integrated within the fuel tank. an o-ring seal attached to the pump's electronic housing does not meet specifications and water can bypass this seal and contact the pump electronics. Consequence: engine stalling, or a failure to start, could occur without prior warning. if stalling were to occur while the motorcycle was being driven, the rider would be unable to maintain speed or accelerate and a crash could occur without prior warning. Action: dealers will replace a sealing ring. if the fuel pump electronic unit is corroded, it will be replaced free of charge. the recall began may 9, 2005. additional my 2005 r1200 gs motorcycles were added to this recall in december 2005. owners of my 2005 motorcycles will receive a notification during february 2006 through august 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 03/03/2005 | |
| 2005 BMW R1200 GS Manufactured between: 09/30/2004 and 10/28/2004 Defect: on certain motorcycles, an adapter in the rear brake line connects a rigid section to a flexible section. if the rigid section is not properly engaged in the adapter, it is possible for a leak to develop. Consequence: brake fluid loss could result. the rear braking capability would not be possible, increasing the risk of a crash. Action: dealers will inspect the rear brake line and adapter. if the inspection reveals that the rigid section of the brake line is not properly engaged in the adapter, then the entire adapter will be replaced. the recall began december 15, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 12/06/2004 | |
| 2005 BMW R1200 GS Manufactured between: 01/05/2004 and 03/16/2004 Defect: on certain motorcycles, the integral anti-lock brake system (iabs) sensor sealing o-ring connection at the rear axle housing may be damaged. an oil leak may develop. Consequence: if this happens, oil could contact the rear wheel and the rear wheel brake disk, and the rider may not be able to control the motorcycle. a crash could occur. Action: dealers will replace the rear wheel iabs sensor sealing o-ring. the recall began july 14, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 06/22/2004 | |
| 2004 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2004 BMW R1200 GS Manufactured between: 01/01/2004 and 02/28/2006 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| R1200 GS ADVENTURE RECALLS | Top |
| 2008 BMW R1200 GS ADVENTURE Manufactured between: 02/14/2008 and 02/14/2008 Defect: bmw is recalling 46 my 2008 r1200 r, r1200 gs, and r1200 gs adventure motorcycles. due to a material defect in the intermediate shaft of the transmission, the shaft could break. if this occurred, it is possible for the transmission to seize. Consequence: if this happened, lock-up of the rear tire could occur. it is also possible for the transmission housing to break. if this happened, oil could leak onto the rear whee, increasing the risk of a crash. Action: dealers will replace the gearbox. the recall is expected to begin during july 2008. owners should contact bmw at 1-800-331-1117. Recall Date: 07/01/2008 | |
| 2006 BMW R1200 GS ADVENTURE Manufactured between: 08/30/2006 and 10/12/2006 Defect: on certain motorcycles, the tire inflation valve hole in the rim of the cross-spoke wheel which is equipped with the optional tire pressure monitoring system (tpm) was incorrectly manufactured. a leak may develop at this location possibly causing sudden deflation of the tire. Consequence: if this happened, motorcycle handling and control would be compromised, increasing the risk of a crash. Action: dealers will temporarily deactivate the tpm system, remove the corresponding valves and integral tpm sensors, and then replace them with standard valves. when a permanent repair is available, owners will be notified to bring their vehicles in for reactivation of the tpm system and replacement of the integral tpm sensors and valves. the recall began on january 12, 2007. owners may contact bmw at 1-800-331-1117. Recall Date: 12/21/2006 | |
| R1200 HP2 RECALLS | Top |
| 2006 BMW R1200 HP2 Manufactured between: 08/01/2005 and 08/31/2006 Defect: on certain motorcycles, during assembly, the final-drive assembly o-ring may not have been installed correctly. a leak may occur at the location of this o-ring which is near the rear brake disc. Consequence: if a leak were to occur, oil could come into contact with the rear brake disc, increasing the risk of a crash. Action: dealers will install a new o-ring in the final-drive assembly. the recall began on october 27, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 10/18/2006 | |
| 2006 BMW R1200 HP2 Manufactured between: 12/09/2005 and 01/20/2006 Defect: on certain motorcycles, the clutch components could become loose while the motorcycle is being operated. Consequence: if this happened, the components could exit through the engine casting increasing the risk of a crash. Action: dealers will install new clutch components free of charge. all motorcycles are located at dealers. no motorcycles have been sold to customers. Recall Date: 04/04/2006 | |
| R1200 R RECALLS | Top |
| 2008 BMW R1200 R Manufactured between: 02/12/2008 and 02/14/2008 Defect: bmw is recalling 46 my 2008 r1200 r, r1200 gs, and r1200 gs adventure motorcycles. due to a material defect in the intermediate shaft of the transmission, the shaft could break. if this occurred, it is possible for the transmission to seize. Consequence: if this happened, lock-up of the rear tire could occur. it is also possible for the transmission housing to break. if this happened, oil could leak onto the rear whee, increasing the risk of a crash. Action: dealers will replace the gearbox. the recall is expected to begin during july 2008. owners should contact bmw at 1-800-331-1117. Recall Date: 07/01/2008 | |
| 2008 BMW R1200 R Manufactured between: 08/30/2006 and 02/05/2008 Defect: bmw is recalling 3,248 my 2007-2008 r1200r, my 2006-2007 r1200 gs and my 2007 r1200 st motorcycles. due to the current routing of the front brake lines, it is possible that during riding, the brake lines could be under strain. if the vibration/strain is significant, the brake lines could split and start to develop a leak. if the leak became significant, brake fluid could escape. if this happened, the level of fluid in the reservoir of the front brake system could drop. Consequence: if fluid level drops significantly, the front brakes could fail increasing the risk of a crash. Action: dealers will inspect and install new brake lines with a modified routing free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/05/2008 | |
| 2007 BMW R1200 R Manufactured between: 03/26/2007 and 05/04/2007 Defect: bmw is recalling 428 my 2007 f800 s, f800 st, r1200 r, k1200 s, k1200 r, k1200 r sport, and k1200 gt motorcycles. it is possible for the coating to separate from the inside face of the steering damper housing. if this happened, the coating could partially clog the oil bores within the damper. Consequence: if this occurred, the steering damper could become stiff increasing the risk of a crash. Action: dealers will replace the steering damper free of charge. the recall is expected to begin during july 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 07/25/2008 | |
| 2007 BMW R1200 R Manufactured between: 08/30/2006 and 02/05/2008 Defect: bmw is recalling 3,248 my 2007-2008 r1200r, my 2006-2007 r1200 gs and my 2007 r1200 st motorcycles. due to the current routing of the front brake lines, it is possible that during riding, the brake lines could be under strain. if the vibration/strain is significant, the brake lines could split and start to develop a leak. if the leak became significant, brake fluid could escape. if this happened, the level of fluid in the reservoir of the front brake system could drop. Consequence: if fluid level drops significantly, the front brakes could fail increasing the risk of a crash. Action: dealers will inspect and install new brake lines with a modified routing free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/05/2008 | |
| R1200 RT RECALLS | Top |
| 2006 BMW R1200 RT Manufactured between: 09/01/2005 and 12/31/2005 Defect: on certain motorcycles, under rapid, repeated, and unusually harsh braking, loss of abs capability could temporarily occur. Consequence: temporary loss of abs braking could increase the risk of a crash. Action: dealers will add a physical restriction, in the form of a banjo bolt with a flow restrictor to the brake line, and on certain models dealers will install new front brake discs of a slightly larger thickness free of charge. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 05/15/2006 | |
| 2006 BMW R1200 RT Manufactured between: 12/01/2004 and 12/31/2005 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| 2006 BMW R1200 RT Manufactured between: 12/09/2005 and 02/16/2006 Defect: on certain motorcycles, the clutch components could become loose while the motorcycle is being operated. Consequence: if this happened, the components could exit through the engine casting increasing the risk of a crash. Action: dealers will install new clutch components free of charge. all motorcycles are located at dealers. no motorcycles have been sold to customers. Recall Date: 04/04/2006 | |
| 2005 BMW R1200 RT Manufactured between: 12/01/2004 and 12/31/2005 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| 2005 BMW R1200 RT Manufactured between: 10/10/2004 and 03/03/2005 Defect: on certain motorcycles, exposure of the throttle housing to road debris could fall and become caught between the throttle-body and the engine block. Consequence: this could restrict movement of the throttle-cable pulley that, in turn, could affect throttle operation and increase the risk of a crash. Action: dealers will install a cover over the throttle-cable pulley free of charge. the recall began on may 10, 2005. owners may contact bmw at 1-800-831-1117. Recall Date: 04/27/2005 | |
| R1200 S RECALLS | Top |
| 2007 BMW R1200 S Manufactured between: 04/01/2006 and 08/31/2006 Defect: on certain motorcycles, during assembly, the final-drive assembly o-ring may not have been installed correctly. a leak may occur at the location of this o-ring which is near the rear brake disc. Consequence: if a leak were to occur, oil could come into contact with the rear brake disc, increasing the risk of a crash. Action: dealers will install a new o-ring in the final-drive assembly. the recall began on october 27, 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 10/18/2006 | |
| R1200 ST RECALLS | Top |
| 2007 BMW R1200 ST Manufactured between: 01/30/2007 and 06/15/2007 Defect: bmw is recalling 3,248 my 2007-2008 r1200r, my 2006-2007 r1200 gs and my 2007 r1200 st motorcycles. due to the current routing of the front brake lines, it is possible that during riding, the brake lines could be under strain. if the vibration/strain is significant, the brake lines could split and start to develop a leak. if the leak became significant, brake fluid could escape. if this happened, the level of fluid in the reservoir of the front brake system could drop. Consequence: if fluid level drops significantly, the front brakes could fail increasing the risk of a crash. Action: dealers will inspect and install new brake lines with a modified routing free of charge. the recall is expected to begin during june 2008. owners may contact bmw at 1-800-831-1117. Recall Date: 06/05/2008 | |
| 2006 BMW R1200 ST Manufactured between: 12/01/2004 and 01/31/2006 Defect: on certain motorcycles, if certain procedures are performed that involves removal of the front left brake caliper, the abs sensor cable can be routed incorrectly and when the caliper is reinstalled, the sensor cable can come into contact and rub against the front brake disc. overtime, if the chafing becomes severe, it is possible to lose the abs function. Consequence: loss of abs function could increase the risk of a crash during certain riding conditions. Action: dealers will attach additional retaining clips free of charge to the abs sensor cable, which will provide a more secure connection to the wheel carrier. the recall began on june 5, 2006, and will be a phased mailing through october 2006. owners may contact bmw at 1-800-831-1117. Recall Date: 04/24/2006 | |
| R850 R RECALLS | Top |
| 2004 BMW R850 R Manufactured between: 10/01/2003 and 11/30/2003 Defect: on certain motorcycles, the front spring strut upper stud bolt weld can fail. this could cause the bolt to break. Consequence: if this happens, the rider may not be able to control the motorcycle, which could cause a crash without warning. Action: dealers will replace the front spring strut. the recall began during june 2004. owners should contact bmw at 1-800-331-1117. Recall Date: 05/19/2004 | |
| X5 RECALLS | Top |
| 2008 BMW X5 Manufactured between: 03/18/2008 and 03/18/2008 Defect: bmw is recalling 55 my 2008 x5 sport utility vehicles for problems with the rear axle stabilizer (anti-sway bar). these vehicles were equipped with a sports-suspension stabilizer rather than a standard suspension stabilizer on the rear axle. Consequence: in certain driving conditions, such as fast lane changes at high speed, the vehicle could experience an 'over-steer' behavior affecting vehicle handling and control, which could increase the risk of a crash. Action: dealers will replace the rear axle stabilizer. the recall is expected to begin during april 2008. owners may contact bmw at 1-800-831-1117 or via e-mail to customerrelations@bmwusa.com. Recall Date: 04/11/2008 | |
| 2007 BMW X5 Manufactured between: 10/02/2006 and 06/27/2007 Defect: on certain vehicles equipped with v8 engines, in conditions of below freezing temperatures combined with low humidity, it is possible for electrostatic discharge to occur at the fuel rails. if this were to occur, the engine electronic control unit (ecu) could be affected so that engine stalling could result. Consequence: if stalling were to occur, the driver may not be able to maintain vehicle speed or accelerate and the power steering could fail increasing the risk of a crash. Action: dealers will attach two ground cables in the engine compartment free of charge. the recall began on october 29, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 10/12/2007 | |
| 2007 BMW X5 Manufactured between: 02/05/2007 and 04/30/2007 Defect: certain passenger vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 135, "passenger car brake systems." the cap of the brake fluid reservoir has been designed in orderto recognize a low fluid level of the hydraulic brake system by triggering a red warning lamp in the instrument cluster. a switch that is attached to this cap could malfunction at high temperatures. Consequence: if this happened, the red warning lamp in the instrument cluster would not be activated. loss of the hydraulic brake system may cause increased stopping distances which could result in a crash. Action: dealers will replace the brake fluid reservoir cap free of charge. the recall began on september 20, 2007. owners may contact bmw at 1-800-831-1117. Recall Date: 08/29/2007 | |
| 2006 BMW X5 Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2005 BMW X5 Manufactured between: 08/01/2005 and 09/30/2005 Defect: certain passenger vehicles may have been built with an incorrectly manufactured automatic transmission parking pawl guide plate. Consequence: this could cause the parking lock system not to engage, after the transmission is placed in the park ("p") position. if the vehicle was parked on an incline, and the parking brake was not engaged, this could result in a vehicle rollaway condition. Action: dealers will repair and replace the automatic transmission guide plate free of charge. the recall began on november 30, 2005. owners may contact bmw at 1-800-332-4269. Recall Date: 11/01/2005 | |
| 2005 BMW X5 Manufactured between: 07/08/2005 and 07/19/2005 Defect: on certain sport utility vehicles, the attachment of the brake line support bracket within the front left wheel well was not welded according to specifications. it could loosen and over time the brake hose could rub against the wheel well. Consequence: the front left brake hose could become damaged to the point where a loss of brake fluid could occur increasing the risk of a crash. Action: dealers will re-attach the brake line support bracket to the front left wheel well free of charge. the recall began on september 20, 2005. owners may contact bmw at 1-800-831-1117. Recall Date: 08/26/2005 | |
| 2004 BMW X5 Manufactured between: 08/25/2003 and 04/15/2004 Defect: on certain passenger vehicles with 3.0 l engines and manual transmissions, if the vehicle is in first gear, and moving slowly, with the accelerator pedal held in a constant position of low engine speed and with the clutch pedal held in a partially depressed position, engine speed may increase. Consequence: the vehicle could accelerate unexpectedly, which could result in a crash. Action: dealers will reprogram the vehicle's digital engine management control unit. the recall began on september 8, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 08/18/2004 | |
| 2004 BMW X5 Manufactured between: 04/05/2004 and 04/24/2004 Defect: on certain sport utility vehicles, the in-tank fuel line may have been attached incorrectly. Consequence: engine stalling could occur, even though the vehicle's fuel gauge indicates that fuel is present in the tank. depending upon traffic and road conditions, this could result in a crash. Action: dealers will inspect the in-tank suction jet pump fuel line and if necessary, reattach according to specifications. this recall began september 9, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 08/13/2004 | |
| 2004 BMW X5 Manufactured between: 05/12/2004 and 07/06/2004 Defect: on certain passenger vehicles equipped with 8 and 12 cylinder engines, the digital engine management control (emc) units were not produced according to specifications. Consequence: as a result, engine stalling will occur after a short period of operation. the vehicle may not be able to restart. also, a loss of power steering and, after repeated actuation of the brake pedal, a loss of brake power assist will occur. these conditions could result in a vehicle crash. Action: dealers will install a new digital engine management control unit. the recall began on july 16, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 07/14/2004 | |
| 2004 BMW X5 Manufactured between: 09/16/2003 and 10/09/2003 Defect: on certain sport utility vehicles, the bolts that hold the front differential, the right output shaft housing flange at the engine, and the right-hand engine support may be insufficiently tightened. Consequence: with prolonged driving, these bolts could become loose, cause damage to the engine and transmission housings. the right output shaft could become disconnected, affecting the ability to control the vehicle, which could result in a crash. Action: dealers will inspect and retighten the drivetrain fasteners. owner notification began november 28, 2003. owners should contact bmw at 1-800-831-1117. Recall Date: 11/14/2003 | |
| Z4 RECALLS | Top |
| 2004 BMW Z4 Manufactured between: 02/19/2003 and 10/13/2003 Defect: on certain passenger vehicles, under certain environmental conditions, a vapor lock in the fuel pump could occur causing the engine to stall. if this were to happen, the engine would not be able to be restarted for approximately 15 to 20 minutes. Consequence: if stalling were to occur, the driver would be unable to maintain vehicle speed or accelerate, increasing the risk of a crash. Action: dealers will install a resistor in the electrical line powering the fuel pump in order to prevent an occurrence of vapor lock. the recall began may 11, 2004. owners should contact bmw at 1-800-831-1117. Recall Date: 04/12/2004 | |
Recall reports are furnished as a courtesy to our customers and are not represented as complete, definitive or authoritative. |
Copyright ©2006 Ikon Auto |
|
Site Management: Fabien Vegas Corporation
|